Your home's exterior takes a beating every single day — sun, wind, rain, impact. When siding fails, moisture gets in fast and damage follows. Forge Siding sends licensed Siding crews across Baltimore, MD to inspect, repair, and replace with zero guesswork.
We didn't start Forge Siding to push volume — we built it because homeowners in Baltimore kept getting burned by crews who cut corners on material selection, skipped moisture barriers, and left job sites messy. That's not how we work. Every Siding project starts with an honest assessment: we look at your substrate condition, check for existing rot or moisture intrusion, and talk through your options before a single nail goes in.
Our crews are licensed, carry full general liability and workers' comp, and every lead installer has completed manufacturer certification training. We work with fiber cement, engineered wood, vinyl, and steel systems — and we'll tell you straight which one makes the most sense for your home's structure, your local weather patterns, and your budget. No upselling, no pressure.
Siding doesn't fail overnight — it gives you warning signs first. Catch them early and a repair handles it. Miss them, and you're looking at rot, mold, and structural repairs on top of the siding bill.
Hairline cracks look cosmetic but they're water channels. Once moisture gets behind the panel and hits the housewrap — or finds no housewrap at all — sheathing rot starts within one season.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Interior peeling close to an outside wall isn't a paint problem — it's a moisture infiltration problem. Your siding is the likely culprit and ignoring it turns a siding job into a drywall and mold job.
A missing panel after a wind event or impact isn't just cosmetic damage. That exposed sheathing is collecting rain until you replace it. This is one repair that can't wait for a convenient schedule.
Old or failing siding, particularly if the housewrap underneath has deteriorated, acts like a thermal short-circuit. Your HVAC runs harder to compensate, and the bills reflect it before the siding looks obviously bad.
Extreme fading means UV degradation — the protective surface layer is gone. Chalking on older paint-based systems signals the same. At that stage, the panel is no longer blocking UV penetration to the substrate underneath.
From a single damaged panel to a complete re-side on a large commercial property, we handle the full range of exterior cladding work — and we do it with the same crew standards regardless of job size.
Fiber cement is the workhorse material we recommend most in MD's climate — it handles humidity, impact, and UV better than most alternatives and carries manufacturer warranties that actually hold up. We're certified installers for HardiePlank, HardieShingle, and competing fiber cement systems. Installation follows manufacturer specs to the millimeter: correct lap, correct fastener type and spacing, correct clearance from grade and roof surface, and full housewrap integration on every project.
Done right, vinyl siding is durable, low-maintenance, and cost-effective. Done wrong — wrong gauge, wrong fastener pattern, no expansion clearance — it warps in the heat and pulls loose in wind. We use .044" and .046" gauge panels minimum and follow thermal expansion specs precisely for MD's temperature range. Nail hem fastening at 16" centers, 1/32" expansion gap at all trim terminations, and a fully integrated vinyl accessory system so the corners, J-channel, and window trim all work together.
Engineered wood is popular in Baltimore neighborhoods where the traditional wood look matters architecturally but the maintenance demands of real cedar or pine aren't practical. We install with stainless or hot-dipped galvanized fasteners to prevent iron staining at the nail head — a detail that separates a professional installation from a quick flip job.
Our repair crews use the same material standards as our full-installation teams — no caulking over gaps as a permanent fix, no missing sealant at transitions, no shortcuts on housewrap at the repair perimeter. If there's rot in the sheathing behind the damaged panel, we address it during the repair rather than covering it up.
We work with metal panel systems, large-format fiber cement, and commercial-grade vinyl for multi-family and light commercial applications. EIFS compatibility work, expansion joint detailing, and coordination with waterproofing and window subcontractors are all in scope. We carry the insurance requirements for commercial GC work and can provide certified payroll documentation for public projects.
Soffit ventilation is often compromised during re-siding work when installers don't maintain existing vent openings or fail to add ventilation where it was previously missing. We verify soffit net-free vent area against attic square footage before closing up the overhang — because your roofing contractor will find the problem later if we don't.
We built our process around the two complaints we heard from homeowners most: contractors who didn't communicate, and scopes that changed after signing. Here's exactly how a Forge Siding project runs from start to finish.
We come out, examine your existing cladding, probe for soft substrate, check flashing and housewrap condition at visible penetrations, and give you an honest assessment of what we're working with. No high-pressure sales — just a clear picture of the project scope before we talk numbers.
You receive a line-by-line written estimate: material cost by product and quantity, labor, removal and disposal of existing siding, and any sheathing repair identified in the assessment. We walk through material options with physical samples, not just catalog photos. You sign off on the spec before we order anything.
Your start date is locked at signing. Crew arrives on time, materials are staged and ready, and the site is protected before demo begins. We run a tight job — no leaving panels exposed overnight when rain is in the forecast.
At project completion, we walk the entire exterior with you. Every run of siding, every corner, every trim termination — you look at it before we close out. If anything isn't right, it gets fixed on the spot. Our goal is that you refer us to your neighbor the week after the project wraps.
Every crew that works on your home carries a current contractor's license for MD, full general liability, and workers' compensation. We'll email you the certificates before we arrive — not after you ask three times.
You see the number before you sign — and the invoice matches the estimate. If scope changes come up during demo, we stop work, show you what we found, and get written approval before proceeding. No invoice surprises.
We run our calendar tightly so the start date we give you is the date we're there. If a legitimate delay comes up — major weather, material shortage — we call you the day before and reschedule immediately, not a week later.
We've seen what happens when crews leave siding debris sitting for a week. Nails in the lawn, panels blocking access, dust in the HVAC intake. Our cleanup protocol runs end-of-day, not end-of-project.
Our workmanship warranty covers what we did and how we did it. The product carries the manufacturer's own warranty on top of ours. That means your home is protected twice — by the material the manufacturer stands behind, and by the installation Forge Siding guarantees.
Get the Details on Our Warranty — +1-844-782-0929Straight from the homeowners we've worked with across Baltimore and Baltimore, MD.
We had three other quotes before calling Forge Siding. The difference was the inspection — they actually walked the whole house with a moisture meter and found soft sheathing behind two panels on the north wall that nobody else mentioned. The estimate covered the sheathing repair too, so no surprise charges when demo day came. Final result is clean and tight. We'd hire them again without hesitation.
A storm took out a whole section of vinyl on the east side of our house. I called four contractors — three of them said they'd have to replace the entire elevation because they couldn't match the profile. Forge Siding's estimator sourced a matching panel through their supplier network and did a clean repair. You can't tell where the new material starts. Saved us probably $4,000 compared to a full-side re-do.
We went with insulated vinyl — Forge Siding recommended the insulated backer for our exposure and the energy savings have been real. First heating season after the install, our gas bill dropped noticeably. Installation crew was professional, on time every day, and the lead installer walked me through every elevation before he called the project done.
I had a specific architectural profile I wanted for the gable ends — a shingle exposure pattern — and everyone else told me it was a custom order with a six-week wait. Forge Siding had it in stock through their regional supplier and we started within two weeks of signing. The detail work at the gable peaks is clean and exact. Not every contractor has the skill to do that level of trim work.
I'm a home inspector by trade, so I know what cutting corners on a siding installation actually looks like behind the panels. Forge Siding's work is correct — right fastener pattern, proper clearances from grade and roofline, continuous housewrap with taped seams at all penetrations. This is how it's supposed to be done and most of the crews I see in Baltimore, MD don't do it this way.
We had three bids and Forge Siding was the only contractor who physically checked the housewrap condition before quoting. Everyone else just looked at the surface. They found a section of torn WRB behind the garage bay that needed patching and included it in the estimate. When you're spending this much on an exterior, you want a company that checks the whole wall system, not just what they can see from the ground.
Real questions, real answers — no filler.
We're not a national call center subcontracting your project to whoever's available. Our crews are based in and around Baltimore, MD. We know local code requirements, local supplier lead times, and local weather patterns — and that local knowledge shows up in how the project runs.
Reach us at +1-844-782-0929 and we'll confirm service at your location. Most addresses in and around Baltimore are within our standard service radius with no travel fee.
Free written estimate. Licensed crew. Scheduled start date. Call Forge Siding now and get a real assessment — not a ballpark number over the phone.
Schedule My Assessment — +1-844-782-0929